Sewage treatment equipment
working principle
The cyclone desander is a new type of separation device based on the principle of sieving of solid particles in the fluid when the sand particles are rotated in the sand remover, and then combined with filtering measures. When the water flows at a certain pressure After entering the equipment from the water inlet of the desander, it will produce a strong rotary motion. Due to the different density of sand and water, the water with low density will rise under the action of centrifugal force, centripetal force, buoyancy and fluid drag. The nozzle is discharged, and the dense sand is discharged from the sewage outlet at the bottom of the equipment. The individual fine particles floating along the water flow are blocked by the second-stage filtering device, thereby achieving the purpose of sand removal, compared with the current cyclone desilter on the market. In comparison, the filter unit is added (the filter accuracy can be selected by the user), which has the advantages of high sand removal rate, saving installation space, low leakage rate for individual tiny solids, and stable working condition.
Features
1. Avoid secondary pollution of water quality in other sand removal methods.
2, the structure is simple, the cost is low, and it is easy to install and operate.
3, small size, large processing capacity, saving on-site installation space.
Selection instructions
When the swirling sand remover is selected, the large model equipment is preferred under the premise of satisfying the flow rate, and it is recommended to replace the large equipment in parallel with several devices in the system.
Technical Parameters
1. Influent turbidity ≤ 320 degrees 2, effluent turbidity ≤ 10 degrees 3, inlet water pressure ≥ 0.4Mpa4, pressure loss 0.028Mpa5, sand removal diameter > 0.8mm
Use installation considerations
1. Equipment installation should be installed in bypass mode to meet the needs of maintenance equipment and cleaning of the filter without stopping the machine.
2. It is forbidden to turn on the equipment for a long time in the no water state
3. Equipment operation:
(1) Sewage rate: When the inlet and outlet pressure difference reaches 0.03-0.06MPa (or according to the system setting pressure difference), it should be backwashed. When the water quality is poor or the new system is used for the first time, backwash for 1-2 minutes every 8 hours. After normal operation, it depends on the water quality.
(2) Backwashing: Open the bypass valve, drain valve, close the inlet valve of the equipment, and rinse the filter with water to clean the filter. The backwashing time depends on the water quality, usually 10-30 seconds.
(3) For systems with serious pollution, a short-cycle high-frequency backwashing process should be used. When the inlet pressure is 0.25MPa, the anti-washing pump should be set separately to increase the backwashing force and increase the amount of sewage.
(4) Return to work status.
A: close the drain valve;
B: Open the inlet valve and close the bypass valve.
Cyclone desander specification model list
Sewage treatment equipment
Selection instructions
1. Equipment selection
(1). Before equipment selection, it must be clear:
a. The nominal diameter and connection method of the pipeline connecting the inlet and outlet of the desander;
b. Work pressure;
c. Swirl direction and relative position of the nozzle.
(2). According to the system processing flow or filtration accuracy, multiple “swirl sand removal (soil) devices†can be selected for series or parallel use.
(3). For systems with high precision requirements, the filter with higher precision should be selected after the “swirl sand removal (soil) device according to the requirements of filtration accuracy to avoid system blockage.
2. Equipment installation
(1). Installation diagram
(2). The equipment can be installed directly on the ground or on a large foundation, and the ground or foundation must be level.
(3). The equipment inlet and outlet pipes and installation direction must be strictly in accordance with the identification on the equipment.
(4). The distance of the equipment casing should not be less than 300mm in principle.
3. Equipment use
(1) When opening the drain valve, use even force to avoid human damage.
(2) After the initial operation of the new system for 48 hours, open the hand hole to check the debris in the cleaning machine.
Slewing Mechanism and Spare Parts
The Slewing Mechanism and Spare Parts for Tower Crane is consisted of Tower Crane Slewing Motor, hydraulic coupling,electromagnetic disk brake and Slewing Reducer. Tower Crane Motor can be different series according to user's requirements. The Slewing Mechanism has features of compact structure, stable operation, high transmission efficiency, low noise, long service life, high reliability,etc. Crane Slewing Mechanism is one of the three main mechanisms of tower crane.
BQ is one of the leading tower crane manufacture in China, our tower cranes and related spare parts are not only in good quality but also have competitive price, and our professional service is also praised by customers all over the world.
Slewing Motor, Tower Crane Spare Part,Slewing Mechanism,Slewing Reducer, Crane Slewing Mechanism,Tower Crane Slewing Motor
SHEN YANG BAOQUAN BUSINESS CO., LTD , https://www.sytopkittowercrane.com