The concentrator is an inverted cone, as shown below. The upper center of the body is equipped with a feeding cylinder, which is connected to the feeding pipe in the tangential direction. A radial grid is welded inside the cylinder to prevent the slurry from rotating. The upper part of the body is equipped with an annular overflow trough, and the lower part of the body is connected with a cone bottom. The both sides of the cone bottom are equipped with a grit discharge pipe and a high pressure water pipe. The lower part of the bottom of the cone is provided with a sand discharging valve for sand discharge and drainage during accident or maintenance. The angle of the cone is generally 55° or 60°. When the ore is contained in the mud, the angle is generally 55°. When the cone angle is less than 55°, the height of the body will increase when the settlement area is the same.
The main purposes of the concentrate bucket in beneficiation are: (1) concentrated dewatering of the original pulp before grinding. (2) Concentration and de-sludge of the overflow of the slurry grade tank before the shaker operation. Re-election, flotation, magnetic separation products or coal sludge dewatering. (3) centrifuges, belt chute and other sorting operations prior to dewatering mines. The concentration concentration of the concentration bucket can reach 60-65%.
There are various sizes of concentrate buckets currently used in production. But commonly used are Ñ„2000 and Ñ„3000 mm. Its maximum feed size is 2 to 0 mm. The separation particle size used for deliming is generally 0.074 mm or 0.037 mm.
The concentrating hopper has a simple structure and does not consume power, and can play a role of storing, concentrating and deliming to a certain extent. However, the sedimentation area is small, the mud removal efficiency is low, and the configuration height difference loss is large. It is generally only suitable for the initial dewatering of mineral processing products, and the overflow is sent to the next step and sometimes needs to be dehydrated again.
When the concentrator is used as a dewatering equipment , its area can be calculated as the amount of solids in the ore. When processing 1.5 ~ 0 mm size, the production capacity is 48 ~ 52 tons / (m 2 · day); when processing 0.074 ~ 0 mm size, the production capacity is 4.5 ~ 6 tons / (m 2 · day).
When the concentration hopper is used for deliming, the rising liquid flow velocity Ï… a should be less than the final sedimentation velocity V 0 of the critical particles:
Where W 0 ——— overflow flow, m 3 /s;
A—the required concentration of the bucket, m 2 ;
K———area coefficient, generally 0.65～0.75, and the diameter is small and takes a low value;
υ 0 ———The free settling velocity of the largest particles allowed to be carried away in the overflow, m/s, is measured by the test or approximated by the Stokes formula.
The relationship between the area required by the concentrator and the diameter:
Where D———concentrator diameter, m.
Environmental Cast Film Machine
Film Structure 357
Screw aspect ratio 32: 132:132:1
Screw direct 75:125:7575:75:90:75:7575:65:75:65:75:65:75
Mold width 250025002500
Finished product width 220022002200
Finished product thickness 0.03mm-0. 2mm0.03mm-0.2mm0.03mm-0.2mm
Maximum extrusion capacity 10 tons/24 hours 10 tons/24 hours 10 tons/24 hours
Mechanical design line speed 160160160
Total power 350KW365KW380KW
Environmental protection film casting production line
Mainly used in the production of biodegradable cast film products
PLA biodegradable cast film can be quickly and naturally decomposed under certain conditions, which is an inevitable trend in the future development of flexible packaging and is widely used as printing materials.
Materials, packaging materials, food daily chemical soft packaging materials, biodegradable coated paper, clothing packaging, etc.
1 PLA is a polymer composed of small lactic acid units (polylactic acid). Lactic acid is an organic acid that plays an important role in our daily life. we flat
The yogurt or anything with glucose can be converted into lactic acid, and the lactic acid of PLA consumables comes from corn, and the starch raw material extracted from corn
material made.
|The degradable film not only has the functions and characteristics of traditional plastics, but also can pass through the action of microorganisms in soil and water or through
The role of ultraviolet rays in the sun, split and degrade in the natural environment, and then re-enter the ecological environment in a reduced form, returning to nature. Domestic research
The varieties developed have covered photodegradation, photobiodegradation, photooxidative biodegradation, high starch content biodegradation, high calcium carbonate filled photooxidative degradation,
Fully biodegradable, etc. Among them, edible film and water-soluble film are more commonly used.
Environmental Cast Film Machine,Environmental Protection Cast Film Line,Biodegradable Cast Film Machine,Water Soluble Cast Film Machine
Baijia Mechanical Equipment (Huizhou) Co., Ltd. , https://www.castfilmmachine.com