The same agent, different preparation methods, different amounts and effects. The choice of formulation method is based primarily on the nature of the agent, the method of addition, and the function. The following are common methods:
(1) formulated in 5% to 10% aqueous solution, the majority of water soluble agents are used in this method (e.g., xanthate, sodium silicate, copper sulfate).
(2) Solvent preparation. Some water-insoluble agents can be dissolved in special solvents. For example, the white medicine is insoluble in water, but is soluble in 10% to 20% aniline solution, and can be used after being prepared into an aniline mixed solution.
(3) Formulated as a suspension or emulsion. For some solid agents that are not easily soluble, they can be formulated into emulsions. If the solubility of lime in water is small, the lime can be ground to a milky suspension (such as lime milk).
(4) Saponification. For fatty acid collector, saponification is the most commonly used methods, such as flotation of hematite, oxidized paraffin with soaps and tall oil with a collector cooperation. In order to saponify the tall oil, when the preparation is formulated, about 10% of sodium carbonate is added, and heated to form a hot soap solution.
(5) Emulsification. The method of emulsification is mechanical strong stirring, or ultrasonic emulsification, etc., after emulsification of fatty acids and diesel oil, they can increase their dispersion in the pulp and improve the efficacy. It is more effective to add an emulsifier. Emulsified oil (alkyl aryl sulfonate) is added to the milk and diesel oil in water, and many surface active substances can be used as an emulsifier.
(6) Acidification. When a cationic collector is used, since it is poor in water solubility, it must be pretreated with hydrochloric acid or acetic acid before being dissolved in water for flotation.
RNH2+HCL→RNH2CL
RNH3CL≒RNH3++CL-
(7) Aerosol method. This is a new formulation method for strengthening the action of the medicament. Its essence is to use a special spray device to directly add the medicament to the flotation tank after it is atomized in the air medium, so it is also called " Aerosol flotation method". The test proved Japan Taro beneficiation plant, the collector, foaming agents flotation agent, mixed with air aerosol made directly added to the flotation pulp, which not only improves the flotation of copper, lead minerals, and Its drug consumption has dropped significantly. For example, the collector is only 1/3 to 1/4 of the usual dosage, and the foaming agent (methylpentanol) is 1/5 of the usual dosage. The aerosol method in our country also proves that the dosage can be reduced. 30% to 50%.
(8) Electrochemical treatment of the agent. In the solution, the flotation agent is chemically treated by direct current, and the state of the agent itself, the pH value of the solution, and the redox potential value can be changed. Thereby, the concentration of the most active agent component is increased, the critical concentration of the gel particles is increased, and the degree of dispersion of the poorly soluble agent in water is improved.
Installation and precautions of track connecting rod oil seal
The installation steps for the track link oil seal are as follows:
1. Cleaning: Clean the connecting parts to ensure that the surface is flat, clean, and free of grease and dirt.
2. Oil application: Apply a layer of lubricating oil to the connecting parts for better installation.
3. Installation: Gently push the oil seal into the connection area to ensure that the lip of the oil seal is not damaged.
4. Positioning: After positioning the oil seal, press it with your fingers to ensure it is in the correct position.
5. Inspection: Check if the oil seal is installed correctly and ensure that the lip is not damaged.
The precautions are as follows:
Before installation, check if the oil seal is damaged. If the oil seal is damaged, replace it with a new one.
Before installation, ensure that the surface of the connecting parts is flat, clean, and free of grease and dirt.
3. When installing the oil seal, gently push in to avoid damaging the lip of the oil seal.
4. After installation, check whether the oil seal is installed correctly to ensure that the lip is not damaged.
5. During use, the condition of the oil seal should be regularly checked. If any damage or wear is found, the oil seal should be replaced in a timely manner.
Wear ring for excavator,For excavator track,For excavator accessories
Safe Seal Technology Co., Ltd. , https://www.jssafeseal.com