- Model NO.: QDX, QX series submersible pump
- Max.Capacity: >400 L/min
- Material: Aluminum Housing
- Assembly: impeller
- Start Up: Electric Pump
- Application: Submersible Pump, Clarified Water Pump
- Media: Clean Water
- Theory: Centrifugal Pump
- Transport Package: 1PCS/Carton
- Origin: ZheJiang, China
- Max.Head: 10-30m
- Driving Type: Motor
- Structure: Single-stage Pump
- Power: Electric
- Type: Submersible Pump
- Industry: Industry and Agriculture
- Performance: Submersible Pump
- Trademark: kaili
- Specification: 0.5-3HP
- HS Code: 8413709190
  Pump Introduction
   QDX, QX series submersible pump consists of pump, mechanical seal and motor. Pump is at the bottom part of pump, which is adopted centrifugal impeller. Motor which is single-phase or three-phase is at the upper part of pump. Seal is used where pump and motor combine, which is a kind of double-end mechanical seal, O rings are applied to all static joints. Float switch can be equipped to control pump's starting and stopping automatically according to the water level.
Main Application
  This series pump is small and light, which is widely used in countryside for elevating water from well, irrigation, sprinkling and domestic water supply, and also used in draining off water for fishpond and building site.
Work conditions
The pump can work properly and continuously under following operational conditions:
1. Medium is not corrosive,Sand contents should be max. 0.01% by volume and Â
   granular size should be max. 0.2mm.
2. Medium temperature shouldn't be over 40°C and PH should be 6.5-8.5.
3. The pumps should be operated within rated head.
4. The pumps should be fully submerged into water with depth of less than 3m      mad max. the pump should be min. 0.5m over the water bottom and not be insert into sludge.
5.Power frequency should be 50HZ,single phase voltage 220V,three phase voltage 380V,and voltage fluctuation should be 0.9-1.1 times than the rated.
Workplace Show
Features of Kaili Submersible Pump
1. 100% copper wire
2. Chrome-plated pump rotor (more resistant to wear and corrode)
3. Thermal protector
4. High-end bearing and mechanical seal
Material
|
Structure of pump |
Material | Can be selected |
| Pump body | Aluminum | Cast-Iron / Stainless steel |
| Impeller | Aluminum | Stainless steel |
| Pump shaft | 45 # Steel | Stainless steel |
| Cable | / | Arbitrary length |
Specification
| Appellation | Model | Flow | Head (m) |
Power (kW) |
HP | Pipe size | Voltage (v) |
Velocity (r/min) |
||
| m³/h | l/min | (mm) | (inch) | |||||||
| QDX Single-phase Submersible Pump |
QDX 1.5-16-0.37 | 1.5 | 25 | 16 | 0.37 | 0.5 | 25 | 1 | 220 | 2860 |
| QDX 3-20-0.55 | 3 | 50 | 20 | 0.55 | 0.75 | 25 | 1 | |||
| QDX 10-10-0.55 | 10 | 166.7 | 10 | 0.55 | 0.75 | 40 | 1.5 | |||
| QDX 15-7-0.55 | 15 | 250 | 7 | 0.55 | 0.75 | 50 | 2 | |||
| QDX 1.5-32-0.75 | 1.5 | 25 | 32 | 0.75 | 1 | 25 | 1 | |||
| QDX 7-18-0.75 | 7 | 117 | 18 | 0.75 | 1 | 40 | 1.5 | |||
| QDX 10-16-0.75 | 10 | 166.7 | 16 | 0.75 | 1 | 50 | 2 | |||
| QDX 15-10-0.75 | 15 | 250 | 10 | 0.75 | 1 | 65 | 2.5 | |||
| QDX 10-16-0.8 | 10 | 166.7 | 16 | 0.8 | 1.1 | 25/40/50 | 1/1.5/2 | |||
| QDX 1.5-38-1.1 | 1.5 | 25 | 38 | 1.1 | 1.5 | 25 | 1 | |||
| QDX 10-20-1.1 | 10 | 166.7 | 20 | 1.1 | 1.5 | 50 | 2 | |||
| QDX 15-15-1.1 | 15 | 250 | 15 | 1.1 | 1.5 | 65 | 2.5 | |||
| QDX 30-9-1.1 | 30 | 500 | 9 | 1.1 | 1.5 | 80 | 3 | |||
| QDX 15-18-1.5 | 15 | 250 | 18 | 1.5 | 2 | 65 | 2.5 | |||
| QDX 40-9-1.5 | 40 | 667 | 9 | 1.5 | 2 | 80 | 3 | |||
| QDX 65-7-2.2 | 65 | 1083 | 7 | 2.2 | 3 | 100 | 4 | |||
| QX Three-phase Submersible Pump |
QX 3-20-0.55 | 3 | 50 | 20 | 0.55 | 0.75 | 25 | 1 | 380 | 3000 |
| QX 10-10-0.55 | 10 | 166.7 | 10 | 0.55 | 0.75 | 40 | 1.5 | |||
| QX 15-7-0.55 | 15 | 250 | 7 | 0.55 | 0.75 | 50 | 2 | |||
| QX 1.5-32-0.75 | 1.5 | 25 | 32 | 0.75 | 1 | 25 | 1 | |||
| QX 7-18-0.75 | 7 | 117 | 18 | 0.75 | 1 | 40 | 1.5 | |||
| QX 10-16-0.75 | 10 | 166.7 | 16 | 0.75 | 1 | 50 | 2 | |||
| QX 15-10-0.75 | 15 | 250 | 10 | 0.75 | 1 | 65 | 2.5 | |||
| QX 10-20-1.1 | 10 | 166.7 | 20 | 1.1 | 1.5 | 50 | 2 | |||
| QX 15-15-1.1 | 15 | 250 | 15 | 1.1 | 1.5 | 65 | 2.5 | |||
| QX 30-9-1.1 | 30 | 500 | 9 | 1.1 | 1.5 | 80 | 3 | |||
| QX 15-18-1.5 | 15 | 250 | 18 | 1.5 | 2 | 65 | 2.5 | |||
| QX 40-9-1.5 | 40 | 667 | 9 | 1.5 | 2 | 80 | 3 | |||
| QX 65-7-2.2 | 65 | 1083 | 7 | 2.2 | 3 | 100 | 4 | |||
| Sewage Submersible Pump |
QDX 6-12-0.4 | 6 | 100 | 12 | 0.4 | 0.55 | 25/32 | 1/1.5 | 220 | 2860 |
| QDX 10-15-0.75 | 10 | 166.7 | 15 | 0.75 | 1 | 25/40 | 1.5/2 | |||
| QDX 10-18-1.1 | 10 | 166.7 | 18 | 1.1 | 1.5 | 25/40 | 1.5/2 | |||
| QX 10-18-1.1 | 10 | 166.7 | 18 | 1.1 | 1.5 | 25/40 | 1.5/2 | 380 | 3000 | |
| QDX Cast-iron body Submersible Pump |
QDX 3-14-0.37T | 3 | 50 | 14 | 0.37 | 0.5 | 25 | 1 | 220 | 2860 |
| QDX 3-18-0.55T | 3 | 50 | 18 | 0.55 | 0.75 | 25 | 1 | |||
| QDX 3-24-0.75T | 3 | 50 | 24 | 0.75 | 1 | 25 | 1 | |||
| QDX 3-30-1.1T | 3 | 50 | 30 | 1.1 | 1.5 | 25 | 1 | |||
| QDX 6-32/2-1.5T | 6 | 100 | 32 | 1.5 | 2 | 40 | 1.5 | |||
Concrete Pile Pre-stressed/Tension Machine:
Tension Machine is a kind of feedthrough pre-tensioing. It is also called Spun Pile tension jack machine, Pole Tension Machine, prestressed tension machine etc. It is the neccesary equipment to produce Pre-stressed Concrete Spun Pile and prestressed concrete pole products. As the end of the tension rod is connected to the anchor with thread, it can be applied to various forged anchors, chilled iron anchor used for stayed-cable bridge and other similar anchors, as well as pre-tension pulling for pipes. In accordance with actual requirement.
HH Tension Machine's advantages:
1. The large-screen LCD display.
2. Double control mechanism of touch screen and keyboard, high reliability.
3. Directly work after the input of tensioning data, and the oil cylinder will automatically complete the tensioning process to reduce uncertain factor of manual operations and improve the tensile quality.
4. Built-in SD card function, which can save the tensile data to the computer regularly, and check the record at any time.
5. With its own printer, it can print tensile data in working time, avoiding the tedious and unstable manual record and ensuring the traceability of tensegrity data is verified.
Technical Parameter:
1. Oil pump flow: 12L/min
2. Motor power: 7.5kw
3. Rated power: 31.5Kpa
4.Tension force: 2000KN
5. Tension stroke: 200mm
6. Programmable controller of automatic control system + input and output of analog data Color touch screen, USB interface output
7. Control voltage: 380V+24V
8. Accuracy of prestress control:±0.1Mpa
9. Data transmission rate is 100%
Main configuration:
Automatic tension control system, 300T jack, oil pump, lifting trolley, tensioning rod, tensioning head and supporting foot
If you have any questions, please contact with us. Welcome you can visit our Factory.For inqury,Please send mail directly to us.
Concrete Machine,Pre-Stressed Machine,Pre-Stressed Concrete Machine,Concrete Pre-Stressed Machine
Jiangsu Haiheng Building-Materials Machinery Co.,Ltd , https://www.jshaiheng.com